JustPaste.it - Share Text & Images the Easy Way

U-Boot 2013.10-rc2-gb02fcf4 (Feb 06 2014 - 14:11:35), Build: jenkins-OpenWRT-Turris-MASTER-slaves=ubuntu-openwrt-32

CPU0: P2020E, Version: 2.1, (0x80ea0021)

Core: e500, Version: 5.1, (0x80211051)

Clock Configuration:

CPU0:1200 MHz, CPU1:1200 MHz,

CCB:600 MHz,

DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz

L1: D-cache 32 KiB enabled

I-cache 32 KiB enabled

Board: TURRIS1 CPLD: V4.1 PCBA: V4.0

Error, wrong i2c adapter 2 max 2 possible

rom_loc: nor upper bank

SD/MMC : 4-bit Mode

eSPI : Enabled

I2C: Error, wrong i2c adapter 2 max 2 possible

ready

SPI: ready

DRAM: Detected UDIMM 9905428-181.A00LF

2 GiB (DDR3, 64-bit, CL=6, ECC off)

Flash: 16 MiB

L2: 512 KiB enabled

NAND: 256 MiB

MMC: FSL_SDHC: 0

*** Warning - bad CRC, using default environment

PCIe1: Root Complex of mini PCIe SLOT, no link, regs @ 0xffe0a000

PCIe1: Bus 00 - 00

PCIe2: Root Complex of PCIe SLOT, x1, regs @ 0xffe09000

02:00.0 - 168c:0030 - Network controller

PCIe2: Bus 01 - 02

Error, wrong i2c adapter 2 max 2 possible

In: serial

Out: serial

Err: serial

Net: Phy not found

PHY reset timed out

eTSEC1, eTSEC2, eTSEC3 [PRIME]

Hit any key to stop autoboot: 1 ··· 0

BOOT NAND

NAND read: device 0 offset 0x0, size 0x100000

1048576 bytes read: OK

Loading from nand0, offset 0x200000

Image Name: Linux-3.10.18

Created: 2014-02-06 13:15:36 UTC

Image Type: PowerPC Linux Kernel Image (gzip compressed)

Data Size: 1823906 Bytes = 1.7 MiB

Load Address: 00000000

Entry Point: 00000000

WARNING: adjusting available memory to 30000000

## Booting kernel from Legacy Image at 00200000 ...

Image Name: Linux-3.10.18

Created: 2014-02-06 13:15:36 UTC

Image Type: PowerPC Linux Kernel Image (gzip compressed)

Data Size: 1823906 Bytes = 1.7 MiB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

## Flattened Device Tree blob at 00400000

Booting using the fdt blob at 0x400000

Uncompressing Kernel Image ... OK

Loading Device Tree to 03ffa000, end 03fffbfc ... OK

WARNING: could not find compatible node fsl-usb2-mph or fsl-usb2-dr: FDT_ERR_NOTFOUND.

WARNING: could not find compatible node fsl-usb2-dr: FDT_ERR_NOTFOUND.

[ 0.000000] Using P2020 RDB machine description

[ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 1536Mb

[ 0.000000] Linux version 3.10.18 (beast@ubuntu-openwrt) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38891) ) #1 SMP Thu Feb 6 14:15:32 CET 2014

[ 0.000000] CPU maps initialized for 1 thread per core

[ 0.000000] bootconsole [udbg0] enabled

setup_arch: bootmem

mpc85xx_rdb_setup_arch()

[ 0.000000] mpc85xx_rdb_setup_arch: Could not find Quicc Engine node

[ 0.000000] MPC85xx RDB board from Freescale Semiconductor

arch: exit

[ 0.000000] Zone ranges:

[ 0.000000] DMA [mem 0x00000000-0x1fffffff]

[ 0.000000] Normal empty

[ 0.000000] HighMem [mem 0x20000000-0x7fffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00000000-0x7fffffff]

[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts

[ 0.000000] PERCPU: Embedded 7 pages/cpu @c13d8000 s6816 r8192 d13664 u32768

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523264

[ 0.000000] Kernel command line: root=/dev/mtdblock8 rw rootfstype=jffs2 console=ttyS0,115200

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Sorting __ex_table...

[ 0.000000] Memory: 2010296k/2097152k available (3520k kernel code, 86856k reserved, 156k data, 209k bss, 180k init)

[ 0.000000] Kernel virtual memory layout:

[ 0.000000] * 0xfffbf000..0xfffff000 : fixmap

[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs

[ 0.000000] * 0xffbfd000..0xffc00000 : early ioremap

[ 0.000000] * 0xe1000000..0xffbfd000 : vmalloc & ioremap

[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1

[ 0.000000] Hierarchical RCU implementation.

[ 0.000000] NR_IRQS:512 nr_irqs:512 16

[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs

[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff

[ 0.000000] mpic: Initializing for 256 sources

[ 0.000000] mpc85xx_rdb_pic_init: Could not find qe-ic node

[ 0.000000] clocksource: timebase mult[d555555] shift[24] registered

[ 0.006300] pid_max: default: 32768 minimum: 301

[ 0.010965] Mount-cache hash table entries: 512

[ 0.016955] mpic: requesting IPIs...

[ 0.021062] Brought up 2 CPUs

[ 0.024533] NET: Registered protocol family 16

[ 0.036094] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1

[ 0.043936] PCI host bridge /pcie@ffe09000 (primary) ranges:

[ 0.049582] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000

[ 0.056797] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000

[ 0.063933] /pcie@ffe09000: PCICSRBAR @ 0xfff00000

[ 0.068972] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0

[ 0.076813] PCI host bridge /pcie@ffe0a000 ranges:

[ 0.081677] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000

[ 0.088891] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000

[ 0.096026] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000

[ 0.110154] PCI: Probing PCI hardware

[ 0.113920] fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00

[ 0.119946] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]

[ 0.126105] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff]

[ 0.132973] pci_bus 0000:00: root bus resource [bus 00-ff]

[ 0.138484] pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)

[ 0.154210] pci 0000:00:00.0: PCI bridge to [bus 01-ff]

[ 0.159526] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02

[ 0.165544] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])

[ 0.174491] pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff]

[ 0.181358] pci_bus 0001:02: root bus resource [bus 02-ff]

[ 0.186862] pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01)

[ 0.194731] pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring

[ 0.202769] pci 0001:02:00.0: PCI bridge to [bus 03-ff]

[ 0.208009] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000)

[ 0.214808] pci 0000:01:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]

[ 0.222018] pci 0000:00:00.0: PCI bridge to [bus 01]

[ 0.226972] pci 0000:00:00.0: bridge window [io 0x0000-0xffff]

[ 0.233058] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]

[ 0.239839] pci 0001:02:00.0: PCI bridge to [bus 03]

[ 0.244793] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]

[ 0.251053] pci 0001:02:00.0: bridge window [mem 0x80000000-0x9fffffff]

[ 0.257831] Some PCI device resources are unassigned, try booting with pci=realloc

[ 0.265398] pci 0000:00:00.0: enabling device (0106 -> 0107)

[ 0.271049] pci 0001:02:00.0: enabling device (0106 -> 0107)

[ 0.279662] bio: create slab <bio-0> at 0

[ 0.284741] Switching to clocksource timebase

[ 0.290331] NET: Registered protocol family 2

[ 0.295036] TCP established hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.302052] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

[ 0.308475] TCP: Hash tables configured (established 4096 bind 4096)

[ 0.314833] TCP: reno registered

[ 0.318003] UDP hash table entries: 256 (order: 1, 8192 bytes)

[ 0.323839] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

[ 0.330202] NET: Registered protocol family 1

[ 0.335699] bounce pool size: 64 pages

[ 0.345707] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.361652] msgmni has been set to 983

[ 0.365402] io scheduler noop registered

[ 0.369249] io scheduler deadline registered (default)

[ 0.418660] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled

[ 0.426917] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A

[ 0.433645] console [ttyS0] enabled, bootconsole disabled

[ 0.444750] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A

[ 0.452051] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550

[ 0.459375] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550

[ 0.467561] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101

[ 0.477584] Amd/Fujitsu Extended Query Table at 0x0040

[ 0.482752] Amd/Fujitsu Extended Query version 1.3.

[ 0.487809] number of CFI chips: 1

[ 0.491433] 6 ofpart partitions found on MTD device ef000000.nor

[ 0.497450] Creating 6 MTD partitions on "ef000000.nor":

[ 0.502768] 0x000000000000-0x000000020000 : "NOR (RO) DTB Image"

[ 0.509306] 0x000000020000-0x0000001c0000 : "NOR (RO) Linux Kernel Image"

[ 0.516577] 0x0000001c0000-0x000000340000 : "NOR (RO) JFFS2 Root File System"

[ 0.524212] 0x000000340000-0x000000e20000 : "NOR (RO) NAND FW backup"

[ 0.531129] 0x000000e40000-0x000000f00000 : "NOR (RW) Cert backup"

[ 0.537793] 0x000000f00000-0x000001000000 : "NOR (RO) U-Boot Image"

[ 0.549520] ONFI param page 0 valid

[ 0.553009] ONFI flash detected

[ 0.556205] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABAEAWP), 256MiB, page size: 2048, OOB size: 64

[ 0.567997] Bad block table found at page 131008, version 0x01

[ 0.574544] Bad block table found at page 130944, version 0x01

[ 0.581023] 3 ofpart partitions found on MTD device ff800000.flash

[ 0.587212] Creating 3 MTD partitions on "ff800000.flash":

[ 0.592701] 0x000000000000-0x000000200000 : "NAND (RW) DTB Image"

[ 0.599344] 0x000000200000-0x000000700000 : "NAND (RW) Linux Kernel Image"

[ 0.606730] 0x000000700000-0x000010000000 : "NAND (RW) JFFS2 Root File System"

[ 0.614540] eLBC NAND device at 0xff800000, bank 1

[ 0.619769] fsl_espi ffe07000.spi: master is unqueued, this is deprecated

[ 0.626569] fsl_espi ffe07000.spi: at 0xe103c000 (irq = 59)

[ 0.632557] ar8216: Module init.

[ 0.636254] libphy: Fixed MDIO Bus: probed

[ 0.640607] libphy: Freescale PowerQUICC MII Bus: probed

[ 0.646263] ar8216: probe addr 0.

[ 0.649710] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033

[ 0.654763] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034

[ 0.659815] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036

[ 0.664970] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033

[ 0.670021] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034

[ 0.675073] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036

[ 0.680228] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033

[ 0.685280] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034

[ 0.690331] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036

[ 0.695486] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd033

[ 0.700537] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd034

[ 0.705589] phy_id: 4dd036, ar8xxx_phy_ids[i]: 4dd036

[ 0.710640] ar8216: gonna list.

[ 0.713778] ar8216: after list.

[ 0.716916] ar8216: Identifying chip.

[ 0.743311] switch0: Atheros AR8327 rev. 2 switch registered on mdio@ffe24520

[ 0.750454] ar8216: FOUND!!!.

[ 1.966143] fsl-gianfar ffe24000.ethernet eth0: mac: 00:00:00:00:00:00

[ 1.972684] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled

[ 1.979477] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256

[ 1.986618] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256

[ 1.994198] fsl-gianfar ffe25000.ethernet eth1: mac: 00:00:00:00:00:00

[ 2.000739] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled

[ 2.007538] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256

[ 2.014680] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256

[ 2.022268] fsl-gianfar ffe26000.ethernet eth2: mac: 00:00:00:00:00:00

[ 2.028809] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled

[ 2.035640] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256

[ 2.042783] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256

[ 2.050040] ucc_geth_driver: QE UCC Gigabit Ethernet Controller

[ 2.056343] i2c /dev entries driver

[ 2.060007] mpc-i2c ffe03000.i2c: timeout 1000000 us

[ 2.067626] rtc-mcp7940 0-006f: rtc core: registered mcp7940 as rtc0

[ 2.074059] mpc-i2c ffe03100.i2c: timeout 1000000 us

[ 2.079361] booke_wdt: powerpc book-e watchdog driver loaded

[ 2.085404] TCP: cubic registered

[ 2.088717] NET: Registered protocol family 17

[ 2.093240] Bridge firewalling registered

[ 2.097257] 8021q: 802.1Q VLAN Support v1.8

[ 2.102903] rtc-mcp7940 0-006f: setting system clock to 2014-09-28 18:26:52 UTC (1411928812)

[ 3.886714] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

[ 3.905646] VFS: Mounted root (jffs2 filesystem) on device 31:8.

[ 3.911851] Freeing unused kernel memory: 180K (c0343000 - c0370000)

procd: Console is alive

procd: - watchdog -

procd: - preinit -

ifconfig: SIOCSIFFLAGS: Cannot assign requested address

sendto(): Network is unreachable

Press the [f] key and hit [enter] to enter failsafe mode

[ 5.450161] usbcore: registered new interface driver usbfs

[ 5.455794] usbcore: registered new interface driver hub

[ 5.461264] usbcore: registered new device driver usb

[ 5.468968] Button Hotplug driver version 0.4.1

[ 5.479040] SCSI subsystem initialized

[ 5.485417] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 5.492019] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller

[ 5.498657] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1

[ 5.505951] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000

[ 5.521051] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00

[ 5.526956] hub 1-0:1.0: USB hub found

[ 5.530725] hub 1-0:1.0: 1 port detected

[ 5.535228] ehci-platform: EHCI generic platform driver

[ 5.545587] sdhci: Secure Digital Host Controller Interface driver

[ 5.551781] sdhci: Copyright(c) Pierre Ossman

[ 5.556528] sdhci-pltfm: SDHCI platform and OF driver helper

[ 5.593044] mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA

[ 5.604010] usbcore: registered new interface driver usb-storage

[ 5.845057] usb 1-1: new high-speed USB device number 2 using fsl-ehci

[ 5.981933] hub 1-1:1.0: USB hub found

[ 5.985823] hub 1-1:1.0: 2 ports detected

mount_root: mounting /dev/root

ifconfig: SIOCSIFFLAGS: Cannot assign requested address

procd: - early -

procd: - watchdog -

procd: - ubus -

procd: - init -

Please press Enter to activate this console.

[ 8.732824] NET: Registered protocol family 10

[ 8.741901] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)

[ 8.764274] Loading modules backported from Linux version master-2013-11-05-0-gafa3093

[ 8.772241] Backport generated by backports.git backports-20130802-0-gdb67a3f

[ 8.823140] usbcore: registered new interface driver ums-alauda

[ 8.830183] usbcore: registered new interface driver ums-cypress

[ 8.837365] usbcore: registered new interface driver ums-datafab

[ 8.844465] usbcore: registered new interface driver ums-freecom

[ 8.851670] usbcore: registered new interface driver ums-isd200

[ 8.858754] usbcore: registered new interface driver ums-jumpshot

[ 8.865971] usbcore: registered new interface driver ums-karma

[ 8.873167] usbcore: registered new interface driver ums-sddr09

[ 8.880331] usbcore: registered new interface driver ums-sddr55

[ 8.887488] usbcore: registered new interface driver ums-usbat

[ 8.898499] xt_time: kernel timezone is -0000

[ 8.911626] cfg80211: Calling CRDA to update world regulatory domain

[ 8.918274] cfg80211: World regulatory domain updated:

[ 8.923475] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 8.931669] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 8.939428] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 8.947183] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 8.954939] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)

[ 8.962696] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)

[ 8.970450] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)

[ 9.029916] PPP generic driver version 2.4.2

[ 9.035198] NET: Registered protocol family 24

[ 9.205587] cfg80211: Calling CRDA for country: US

[ 9.210824] cfg80211: Regulatory domain changed to country: US

[ 9.216707] cfg80211: DFS Master region FCC

[ 9.220828] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 9.229191] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)

[ 9.236991] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)

[ 9.244747] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)

[ 9.252500] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)

[ 9.260260] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)

[ 9.268014] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)

[ 9.275764] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)

[ 9.283704] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xf3540000, irq=24

[ 18.234378] ar8216: Module config init.

[ 18.238580] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 18.246223] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready

[ 18.253960] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready

[ 18.775978] ar8216: Module config init.

[ 18.780092] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

[ 18.787484] device eth0 entered promiscuous mode

[ 18.792496] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready

[ 18.801318] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready

[ 18.807979] device eth1 entered promiscuous mode

[ 18.897811] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready

[ 19.777182] ar8216: config aneg.

[ 20.783319] libphy: mdio@ffe24520:00 - Link is Up - 1000/Full

[ 20.789157] br-lan: port 1(eth0) entered forwarding state

[ 20.794586] br-lan: port 1(eth0) entered forwarding state

[ 20.800020] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[ 20.806377] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

[ 20.812930] libphy: fixed-0:06 - Link is Up - 1000/Full

[ 20.818269] br-lan: port 2(eth1) entered forwarding state

[ 20.823694] br-lan: port 2(eth1) entered forwarding state

[ 20.829120] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready

[ 22.797040] br-lan: port 1(eth0) entered forwarding state

[ 22.825041] br-lan: port 2(eth1) entered forwarding state

[ 24.843401] jffs2: Empty flash at 0x000a25fc ends at 0x000b660c

[ 24.873679] jffs2: notice: (2454) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

procd: - init complete -

procd: Instance log::instance1 s in a crash loop 6 crashes, 0 seconds since last crash