[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.113 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23147-4b8b2f4f97) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Sun May 28 18:22:23 2023
[ 0.000000] Machine model: Bananapi BPI-R3
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff]
[ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff]
[ 0.000000] node 0: [mem 0x000000004ffc0000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 17 pages/cpu s30040 r8192 d31400 u69632
[ 0.000000] pcpu-alloc: s30040 r8192 d31400 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: root=/dev/mmcblk0p65
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2040188K/2097152K available (8384K kernel code, 910K rwdata, 2280K rodata, 448K init, 301K bss, 56964K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.000135] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.000143] pid_max: default: 32768 minimum: 301
[ 0.000363] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.000375] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.001420] rcu: Hierarchical SRCU implementation.
[ 0.001724] smp: Bringing up secondary CPUs ...
[ 0.001983] Detected VIPT I-cache on CPU1
[ 0.002006] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.002034] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.002296] Detected VIPT I-cache on CPU2
[ 0.002307] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.002318] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.002554] Detected VIPT I-cache on CPU3
[ 0.002564] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.002573] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.002598] smp: Brought up 1 node, 4 CPUs
[ 0.002612] SMP: Total of 4 processors activated.
[ 0.002615] CPU features: detected: 32-bit EL0 Support
[ 0.002618] CPU features: detected: CRC32 instructions
[ 0.002641] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.002694] CPU: All CPU(s) started at EL2
[ 0.002704] alternatives: patching kernel code
[ 0.005764] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005785] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.005933] pinctrl core: initialized pinctrl subsystem
[ 0.006554] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.006798] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[ 0.006834] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.006861] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.007108] thermal_sys: Registered thermal governor 'fair_share'
[ 0.007110] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.007114] thermal_sys: Registered thermal governor 'step_wise'
[ 0.007117] thermal_sys: Registered thermal governor 'user_space'
[ 0.007310] ASID allocator initialised with 65536 entries
[ 0.007635] pstore: Registered ramoops as persistent store backend
[ 0.007639] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.017392] cryptd: max_cpu_qlen set to 1000
[ 0.019271] SCSI subsystem initialized
[ 0.019348] libata version 3.00 loaded.
[ 0.020229] clocksource: Switched to clocksource arch_sys_counter
[ 0.020682] NET: Registered PF_INET protocol family
[ 0.020797] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.021455] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.021475] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.021483] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.021549] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[ 0.021722] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.021797] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.021825] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.021944] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.021964] PCI: CLS 0 bytes, default 64
[ 0.024098] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 0.026791] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.026805] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.048898] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.050047] pwm-mediatek 10048000.pwm: clock: top fail: -517
[ 0.050384] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 0.050405] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 0.050415] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 0.050463] phy phy-soc:t-phy@11c00000.0: u3 auto load valid efuse: ENABLE with value: 1
[ 0.050495] phy phy-soc:t-phy@11c00000.0: pcie auto load valid efuse: ENABLE with value: 1
[ 0.050519] phy phy-soc:t-phy@11c00000.0: u3 lane1 efuse - intr 23, rx_imp e, tx_imp d
[ 0.050575] /soc/pcie@11280000: Failed to get clk index: 0 ret: -517
[ 0.050585] mtk-pcie-gen3 11280000.pcie: failed to get clocks
[ 0.053481] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.055189] printk: console [ttyS0] disabled
[ 0.075348] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 122, base_baud = 2500000) is a ST16650V2
[ 0.779838] printk: console [ttyS0] enabled
[ 0.804638] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 123, base_baud = 1625000) is a ST16650V2
[ 0.814491] mtk_rng 1020f000.trng: registered RNG driver
[ 0.814720] random: crng init done
[ 0.820045] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.831258] loop: module loaded
[ 0.834406] Loading iSCSI transport class v2.0-870.
[ 0.840668] spi-nand spi0.0: Winbond SPI NAND was found.
[ 0.845975] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 0.854240] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.860589] Creating 4 MTD partitions on "spi0.0":
[ 0.865364] 0x000000580000-0x000008000000 : "ubi"
[ 0.996962] 0x000000380000-0x000000580000 : "fip"
[ 1.004039] 0x000000080000-0x000000380000 : "reserved"
[ 1.012482] 0x000000000000-0x000000080000 : "bl2"
[ 1.153329] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009880000, irq 134
[ 1.163110] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc009880000, irq 134
[ 1.172645] i2c_dev: i2c /dev entries driver
[ 1.178411] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.186900] NET: Registered PF_INET6 protocol family
[ 1.192467] Segment Routing with IPv6
[ 1.196133] In-situ OAM (IOAM) with IPv6
[ 1.200074] NET: Registered PF_PACKET protocol family
[ 1.205150] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.218165] 8021q: 802.1Q VLAN Support v1.8
[ 1.223160] pstore: Using crash dump compression: deflate
[ 1.233876] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 1.241262] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 1.247516] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 1.255990] phy phy-soc:t-phy@11c00000.0: u3 auto load valid efuse: ENABLE with value: 1
[ 1.264090] phy phy-soc:t-phy@11c00000.0: pcie auto load valid efuse: ENABLE with value: 1
[ 1.265257] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.272352] phy phy-soc:t-phy@11c00000.0: u3 lane1 efuse - intr 23, rx_imp e, tx_imp d
[ 1.285928] mmc0: new high speed SDHC card at address aaaa
[ 1.294450] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
[ 1.307397] Alternate GPT is invalid, using primary GPT.
[ 1.313244] FIT: Selected configuration: "config-mt7986a-bananapi-bpi-r3-snand" (OpenWrt bananapi_bpi-r3 with mt7986a-bananapi-bpi-r3-snand)
[ 1.325836] FIT: kernel sub-image 0x00001000..0x00530f72 "kernel-1" (ARM64 OpenWrt Linux-5.15.113)
[ 1.335737] FIT: flat_dt sub-image 0x00531000..0x00538fff "fdt-1" (ARM64 OpenWrt bananapi_bpi-r3 device tree blob)
[ 1.346938] FIT: flat_dt sub-image 0x00539000..0x00540fff "fdt-mt7986a-bananapi-bpi-r3-nor" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-nor)
[ 1.363079] FIT: flat_dt sub-image 0x00541000..0x00548fff "fdt-mt7986a-bananapi-bpi-r3-emmc-nor" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-emmc-nor)
[ 1.380088] FIT: flat_dt sub-image 0x00549000..0x00550fff "fdt-mt7986a-bananapi-bpi-r3-emmc-snand" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-emmc-snand)
[ 1.397442] FIT: flat_dt sub-image 0x00551000..0x00558fff "fdt-mt7986a-bananapi-bpi-r3-snand" (ARM64 OpenWrt bananapi_bpi-r3 device tree overlay mt7986a-bananapi-bpi-r3-snand)
[ 1.413925] FIT: filesystem sub-image 0x00559000..0x00a41fff "rootfs-1" (ARM64 OpenWrt bananapi_bpi-r3 rootfs)
[ 1.424514] FIT: selecting configured loadable "rootfs-1" to be root filesystem
[ 1.431808] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p65(rootfs-1) p66(rootfs_data)
[ 1.500255] mtk-pcie-gen3 11280000.pcie: PCIe link down, ltssm reg val: 0x1000001
[ 1.507757] mtk-pcie-gen3: probe of 11280000.pcie failed with error -110
[ 1.536332] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 1.545465] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 1.554150] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=142)
[ 1.574467] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=143)
[ 1.594478] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=144)
[ 1.614464] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=145)
[ 1.634448] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=146)
[ 1.645516] DSA: tree 0 setup
[ 1.650654] UBI: auto-attach mtd0
[ 1.653971] ubi0: default fastmap pool size: 45
[ 1.658485] ubi0: default fastmap WL pool size: 22
[ 1.663278] ubi0: attaching mtd0
[ 5.276984] ubi0: scanning is finished
[ 5.322061] ubi0: attached mtd0 (name "ubi", size 122 MiB)
[ 5.327541] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.334408] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.341178] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.348117] ubi0: good PEBs: 980, bad PEBs: 0, corrupted PEBs: 0
[ 5.354106] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 5.361309] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1642748947
[ 5.370418] ubi0: available PEBs: 465, total reserved PEBs: 515, PEBs reserved for bad PEB handling: 20
[ 5.379788] ubi0: background thread "ubi_bgt0d" started, PID 534
[ 5.385900] block ubiblock0_1: created from ubi0:1(rootfs)
[ 5.401756] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 5.409029] Freeing unused kernel memory: 448K
[ 5.470281] Run /sbin/init as init process
[ 5.474362] with arguments:
[ 5.477312] /sbin/init
[ 5.480003] with environment:
[ 5.483133] HOME=/
[ 5.485478] TERM=linux
[ 5.607976] init: Console is alive
[ 5.611506] init: - watchdog -
[ 5.897306] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.919165] usbcore: registered new interface driver usbfs
[ 5.924700] usbcore: registered new interface driver hub
[ 5.930029] usbcore: registered new device driver usb
[ 5.938751] phy phy-soc:t-phy@11e10000.1: u2 auto load valid efuse: ENABLE with value: 1
[ 5.946909] phy phy-soc:t-phy@11e10000.2: u3 auto load valid efuse: ENABLE with value: 1
[ 5.955051] phy phy-soc:t-phy@11e10000.3: u2 auto load valid efuse: ENABLE with value: 1
[ 5.963594] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.968811] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 5.979261] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010
[ 5.988423] xhci-mtk 11200000.usb: irq 126, io mem 0x11200000
[ 5.994245] xhci-mtk 11200000.usb: xHCI Host Controller
[ 5.999455] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 6.006839] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 6.014247] hub 1-0:1.0: USB hub found
[ 6.018012] hub 1-0:1.0: 2 ports detected
[ 6.022282] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.030599] hub 2-0:1.0: USB hub found
[ 6.034349] hub 2-0:1.0: 1 port detected
[ 6.040927] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.058409] init: - preinit -
[ 6.246604] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 6.255052] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 6.265319] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 6.490233] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 6.670876] hub 1-1:1.0: USB hub found
[ 6.674689] hub 1-1:1.0: 4 ports detected
[ 8.706481] F2FS-fs (mmcblk0p66): Mounted with checkpoint version = d70cae1
[ 8.718349] mount_root: switching to f2fs overlay
[ 8.724512] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[ 8.738467] urandom-seed: Seeding with /etc/urandom.seed
[ 8.782090] procd: - early -
[ 8.785013] procd: - watchdog -
[ 9.315743] procd: - watchdog -
[ 9.321721] procd: - ubus -
[ 9.380452] procd: - init -
[ 9.518178] urngd: v1.0.2 started.
[ 9.542489] kmodloader: loading kernel modules from /etc/modules.d/*
[ 9.553735] i2c-gpio i2c-gpio-0: using lines 427 (SDA) and 428 (SCL)
[ 9.560396] i2c-gpio i2c-gpio-1: using lines 429 (SDA) and 430 (SCL)
[ 9.569350] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[ 9.583475] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 9.590987] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 9.602008] sfp sfp1: Host maximum power 3.0W
[ 9.607096] sfp sfp2: Host maximum power 3.0W
[ 10.045494] mt7986-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20221012174743a
[ 10.045494]
[ 10.183325] mt7986-wmac 18000000.wmac: WM Firmware Version: ____000000, Build Time: 20221012174805
[ 10.264218] mt7986-wmac 18000000.wmac: WA Firmware Version: DEV_000000, Build Time: 20221012174937
[ 30.550232] mt7986-wmac 18000000.wmac: Message 00000002 (seq 9) timeout
[ 30.556843] mt7986-wmac 18000000.wmac: Failed to start WA firmware
[ 30.563099] mt7986-wmac: probe of 18000000.wmac failed with error -110
[ 30.582824] PPP generic driver version 2.4.2
[ 30.587716] NET: Registered PF_PPPOX protocol family
[ 30.594956] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 32.516559] mtk_soc_eth 15100000.ethernet eth0: Link is Down
[ 32.528056] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 32.536695] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 32.538664] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 32.553663] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 32.560124] br-lan: port 1(lan1) entered blocking state
[ 32.565399] br-lan: port 1(lan1) entered disabled state
[ 32.572060] device lan1 entered promiscuous mode
[ 32.576671] device eth0 entered promiscuous mode
[ 32.589293] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 32.599176] br-lan: port 2(lan2) entered blocking state
[ 32.604463] br-lan: port 2(lan2) entered disabled state
[ 32.611515] device lan2 entered promiscuous mode
[ 32.620263] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 32.630094] br-lan: port 3(lan3) entered blocking state
[ 32.635405] br-lan: port 3(lan3) entered disabled state
[ 32.642594] device lan3 entered promiscuous mode
[ 32.651251] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 32.663189] mt7530-mdio mdio-bus:1f lan4: Link is Up - 100Mbps/Full - flow control rx/tx
[ 32.668014] br-lan: port 4(lan4) entered blocking state
[ 32.676522] br-lan: port 4(lan4) entered disabled state
[ 32.683965] device lan4 entered promiscuous mode
[ 32.690458] br-lan: port 4(lan4) entered blocking state
[ 32.695684] br-lan: port 4(lan4) entered forwarding state
[ 32.701634] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 32.711179] mt7530-mdio mdio-bus:1f sfp2: configuring for inband/2500base-x link mode
[ 32.720839] br-lan: port 5(sfp2) entered blocking state
[ 32.726062] br-lan: port 5(sfp2) entered disabled state
[ 32.733573] device sfp2 entered promiscuous mode
[ 32.744421] mtk_soc_eth 15100000.ethernet eth1: configuring for inband/2500base-x link mode
[ 32.754610] br-wan: port 1(eth1) entered blocking state
[ 32.759844] br-wan: port 1(eth1) entered disabled state
[ 32.765403] device eth1 entered promiscuous mode
[ 32.771848] br-wan: port 1(eth1) entered blocking state
[ 32.777084] br-wan: port 1(eth1) entered forwarding state
[ 32.784198] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode
[ 32.794208] br-wan: port 2(wan) entered blocking state
[ 32.795915] mt7530-mdio mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control off
[ 32.799340] br-wan: port 2(wan) entered disabled state
[ 32.813565] device wan entered promiscuous mode
[ 32.820354] br-wan: port 2(wan) entered blocking state
[ 32.825479] br-wan: port 2(wan) entered forwarding state
[ 33.591218] br-wan: port 1(eth1) entered disabled state
