JustPaste.it

Kernel log

[    0.000000] Linux version 5.10.146 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19803-9a599fee93) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Oct 14 22:44:41 2022
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is TOTOLINK X5000R
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2,2} total 4
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] On node 0 totalpages: 65536
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] percpu: Embedded 15 pages/cpu s30256 r8192 d22992 u61440
[    0.000000] pcpu-alloc: s30256 r8192 d22992 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Writing ErrCtl register=00040016
[    0.000000] Readback ErrCtl register=00040016
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 249300K/262144K available (7026K kernel code, 631K rwdata, 828K rodata, 1292K init, 243K bss, 12844K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 880MHz
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000013] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[    0.007943] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.017002] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.083163] pid_max: default: 32768 minimum: 301
[    0.087924] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.095127] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.105749] rcu: Hierarchical SRCU implementation.
[    0.110790] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.118891] smp: Bringing up secondary CPUs ...
[    0.124174] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.124185] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.124197] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.124273] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.178699] Synchronize counters for CPU 1: done.
[    0.211195] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.211205] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.211214] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.211264] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.270134] Synchronize counters for CPU 2: done.
[    0.300719] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.300728] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.300736] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.300787] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.355318] Synchronize counters for CPU 3: done.
[    0.385187] smp: Brought up 1 node, 4 CPUs
[    0.393188] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.403007] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.410017] pinctrl core: initialized pinctrl subsystem
[    0.417729] NET: Registered protocol family 16
[    0.423401] thermal_sys: Registered thermal governor 'step_wise'
[    0.424346] cpuidle: using governor teo
[    0.445969] FPU Affinity set after 11720 emulations
[    0.473207] clocksource: Switched to clocksource GIC
[    0.479978] NET: Registered protocol family 2
[    0.484765] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.493649] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.501967] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.509630] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.516715] TCP: Hash tables configured (established 2048 bind 2048)
[    0.523182] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.529657] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.536897] NET: Registered protocol family 1
[    0.541190] PCI: CLS 0 bytes, default 32
[    0.547960] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    0.558534] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.564305] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.574982] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.584018] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.589821] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.595794] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.602175] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.612681] printk: console [ttyS0] disabled
[    0.617040] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[    0.626048] printk: console [ttyS0] enabled
[    0.634301] printk: bootconsole [early0] disabled
[    0.646609] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[    0.653522] spi-nor spi0.0: en25qh128 (16384 Kbytes)
[    0.658540] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.664986] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[    0.672284] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[    0.680377] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[    0.687746] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[    0.695276] Creating 4 MTD partitions on "spi0.0":
[    0.700063] 0x000000000000-0x000000030000 : "u-boot"
[    0.706021] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.712418] 0x000000040000-0x000000050000 : "factory"
[    0.718511] 0x000000050000-0x000001000000 : "firmware"
[    0.724772] 2 uimage-fw partitions found on MTD device firmware
[    0.730691] Creating 2 MTD partitions on "firmware":
[    0.735666] 0x000000000000-0x000000295251 : "kernel"
[    0.740609] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[    0.749832] 0x000000295251-0x000000fb0000 : "rootfs"
[    0.754822] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[    0.764774] mtd: device 5 (rootfs) set to be root filesystem
[    0.770556] 1 squashfs-split partitions found on MTD device rootfs
[    0.776754] 0x000000690000-0x000000fb0000 : "rootfs_data"
[    0.824886] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    0.834563] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[    0.843683] i2c /dev entries driver
[    0.849704] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[    0.856451] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
[    0.865266] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
[    0.873439] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
[    0.881674] mt7621-pci 1e140000.pcie: Parsing DT failed
[    0.888993] NET: Registered protocol family 10
[    0.895243] Segment Routing with IPv6
[    0.899006] NET: Registered protocol family 17
[    0.903612] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.916938] 8021q: 802.1Q VLAN Support v1.8
[    0.924755] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[    0.946725] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=26)
[    0.959081] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27)
[    0.971430] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28)
[    0.983866] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29)
[    0.996262] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30)
[    1.008703] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[    1.019175] DSA: tree 0 setup
[    1.022669] rt2880-pinmux pinctrl: pcie is already enabled
[    1.028288] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[    1.034998] mt7621-pci 1e140000.pcie:   No bus range found for /pcie@1e140000, using [bus 00-ff]
[    1.043798] mt7621-pci 1e140000.pcie:      MEM 0x0060000000..0x006fffffff -> 0x0000000000
[    1.051947] mt7621-pci 1e140000.pcie:       IO 0x001e160000..0x001e16ffff -> 0x0000000000
[    1.060198] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[    1.067929] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[    1.075567] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[    1.182927] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[    1.188511] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[    1.294175] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[    1.301110] mt7621-pci 1e140000.pcie: PCIE0 enabled
[    1.305978] mt7621-pci 1e140000.pcie: PCIE1 enabled
[    1.310839] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[    1.320303] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[    1.326669] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    1.333535] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.340382] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.345871] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[    1.356070] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    1.362067] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.368324] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[    1.375360] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000]
[    1.381148] pci 0000:00:00.0: supports D1
[    1.385154] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    1.391285] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    1.397322] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    1.403593] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid
[    1.410610] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000]
[    1.416411] pci 0000:00:01.0: supports D1
[    1.420404] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    1.427403] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.435415] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.443648] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[    1.449674] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    1.456719] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[    1.463436] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    1.470453] pci 0000:01:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[    1.477153] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    1.484186] pci 0000:01:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[    1.490979] pci 0000:01:00.0: supports D1 D2
[    1.495254] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.501886] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    1.517889] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    1.523111] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
[    1.529212] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.535988] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff pref]
[    1.543199] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.550052] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[    1.556099] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    1.563126] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[    1.569832] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[    1.576862] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[    1.583572] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[    1.590589] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[    1.597394] pci 0000:02:00.0: supports D1 D2
[    1.601646] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.608287] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    1.624358] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[    1.629582] pci 0000:00:01.0:   bridge window [io  0x0000-0x0fff]
[    1.635674] pci 0000:00:01.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.642433] pci 0000:00:01.0:   bridge window [mem 0x60000000-0x600fffff pref]
[    1.649651] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    1.656305] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    1.662889] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    1.669838] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    1.676439] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    1.683388] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    1.690148] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[    1.697356] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[    1.704143] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[    1.711334] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[    1.718115] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[    1.724895] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
[    1.731655] pci 0000:00:01.0: BAR 7: assigned [io  0x1e161000-0x1e161fff]
[    1.738444] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[    1.746187] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[    1.753928] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[    1.761647] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.766613] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
[    1.773389] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.780146] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x602fffff pref]
[    1.787358] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[    1.795100] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[    1.802821] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[    1.810555] pci 0000:00:01.0: PCI bridge to [bus 02]
[    1.815511] pci 0000:00:01.0:   bridge window [io  0x1e161000-0x1e161fff]
[    1.822269] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff]
[    1.829049] pci 0000:00:01.0:   bridge window [mem 0x60400000-0x605fffff pref]
[    1.843938] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.855239] Freeing unused kernel memory: 1292K
[    1.859774] This architecture does not have kernel memory protection.
[    1.866266] Run /sbin/init as init process
[    1.870342]   with arguments:
[    1.870347]     /sbin/init
[    1.870351]   with environment:
[    1.870357]     HOME=/
[    1.870362]     TERM=linux
[    1.870776] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[    2.433406] init: Console is alive
[    2.437201] init: - watchdog -
[    3.173498] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.292537] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.313585] init: - preinit -
[    4.067118] random: jshn: uninitialized urandom read (4 bytes read)
[    4.145090] random: jshn: uninitialized urandom read (4 bytes read)
[    4.184611] random: jshn: uninitialized urandom read (4 bytes read)
[    4.432626] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[    4.441033] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[    4.443758] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[    4.456431] 8021q: adding VLAN 0 to HW filter on device lan1
[    4.464735] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.728267] jffs2: notice: (556) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (9 unchecked, 3 orphan) and 14 of xref (3 dead, 0 orphan) found.
[    8.745931] mount_root: switching to jffs2 overlay
[    8.756016] overlayfs: upper fs does not support tmpfile.
[    8.770723] urandom-seed: Seeding with /etc/urandom.seed
[    8.958030] procd: - early -
[    8.961145] procd: - watchdog -
[    9.613402] procd: - watchdog -
[    9.617805] procd: - ubus -
[    9.701719] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.710380] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.717250] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.734620] procd: - init -
[   10.310377] random: crng init done
[   10.313959] random: 26 urandom warning(s) missed due to ratelimiting
[   10.417209] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.667619] urngd: v1.0.2 started.
[   10.710608] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   10.718247] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   10.918420] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
[   10.923874] pci 0000:00:00.0: enabling device (0004 -> 0007)
[   10.929518] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[   10.936377] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23
[   10.941852] pci 0000:00:01.0: enabling device (0004 -> 0007)
[   10.947539] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[   11.208095] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a
[   11.208095] 
[   11.535775] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052
[   11.573648] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111
[   17.022446] PPP generic driver version 2.4.2
[   17.028621] NET: Registered protocol family 24
[   17.042229] kmodloader: done loading kernel modules from /etc/modules.d/*
[   25.009150] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[   25.026992] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[   25.035341] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   25.039454] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[   25.051038] 8021q: adding VLAN 0 to HW filter on device lan1
[   25.061465] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.069056] br-lan: port 1(lan1) entered blocking state
[   25.074406] br-lan: port 1(lan1) entered disabled state
[   25.080498] device lan1 entered promiscuous mode
[   25.085406] device eth0 entered promiscuous mode
[   25.121795] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[   25.128973] 8021q: adding VLAN 0 to HW filter on device lan2
[   25.138243] br-lan: port 2(lan2) entered blocking state
[   25.143936] br-lan: port 2(lan2) entered disabled state
[   25.150789] device lan2 entered promiscuous mode
[   25.169805] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[   25.176977] 8021q: adding VLAN 0 to HW filter on device lan3
[   25.188810] br-lan: port 3(lan3) entered blocking state
[   25.194126] br-lan: port 3(lan3) entered disabled state
[   25.201566] device lan3 entered promiscuous mode
[   25.221375] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[   25.228584] 8021q: adding VLAN 0 to HW filter on device lan4
[   25.238376] br-lan: port 4(lan4) entered blocking state
[   25.244092] br-lan: port 4(lan4) entered disabled state
[   25.250834] device lan4 entered promiscuous mode
[   25.272292] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[   25.279535] 8021q: adding VLAN 0 to HW filter on device wan
[   27.168062] br-lan: port 5(wlan1) entered blocking state
[   27.173461] br-lan: port 5(wlan1) entered disabled state
[   27.179630] device wlan1 entered promiscuous mode
[   27.424661] br-lan: port 6(wlan0) entered blocking state
[   27.430070] br-lan: port 6(wlan0) entered disabled state
[   27.436217] device wlan0 entered promiscuous mode
[   27.441367] br-lan: port 6(wlan0) entered blocking state
[   27.446782] br-lan: port 6(wlan0) entered forwarding state
[   27.452775] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.614286] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   27.637512] mt7530 mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow control rx/tx
[   27.645195] br-lan: port 4(lan4) entered blocking state
[   27.650484] br-lan: port 4(lan4) entered forwarding state
[   28.103217] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   28.109953] br-lan: port 5(wlan1) entered blocking state
[   28.115554] br-lan: port 5(wlan1) entered forwarding state
[   29.212746] mt7530 mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx
[   29.220213] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready