; generated by Slic3r 1.3.1-dev (Build 54a31eed204863c49dfaa3b6fe4809f6d10a94ba) on 2020-05-23 at 16:39:13
; external perimeters extrusion width = 0.50mm (3.66mm^3/s)
; perimeters extrusion width = 0.50mm (3.66mm^3/s)
; infill extrusion width = 0.50mm (3.66mm^3/s)
; solid infill extrusion width = 0.50mm (3.66mm^3/s)
; top infill extrusion width = 0.50mm (3.66mm^3/s)
<GCODE SNIP>
; avoid_crossing_perimeters = 1
; bed_shape = 74.5891x7.83963,73.3611x15.5934,71.3292x23.1763,68.5159x30.5052,64.9519x37.5,60.6763x44.0839,55.7359x50.1848,50.1848x55.7359,44.0839x60.6763,37.5x64.9519,30.5052x68.5159,23.1763x71.3292,15.5934x73.3611,7.83963x74.5891,0x75,-7.83963x74.5891,-15.5934x73.3611,-23.1763x71.3292,-30.5052x68.5159,-37.5x64.9519,-44.0839x60.6763,-50.1848x55.7359,-55.7359x50.1848,-60.6763x44.0839,-64.9519x37.5,-68.5159x30.5052,-71.3292x23.1763,-73.3611x15.5934,-74.5891x7.83963,-75x0,-74.5891x-7.83963,-73.3611x-15.5934,-71.3292x-23.1763,-68.5159x-30.5052,-64.9519x-37.5,-60.6763x-44.0839,-55.7359x-50.1848,-50.1848x-55.7359,-44.0839x-60.6763,-37.5x-64.9519,-30.5052x-68.5159,-23.1763x-71.3292,-15.5934x-73.3611,-7.83963x-74.5891,0x-75,7.83963x-74.5891,15.5934x-73.3611,23.1763x-71.3292,30.5052x-68.5159,37.5x-64.9519,44.0839x-60.6763,50.1848x-55.7359,55.7359x-50.1848,60.6763x-44.0839,64.9519x-37.5,68.5159x-30.5052,71.3292x-23.1763,73.3611x-15.5934,74.5891x-7.83963,75x0
; bed_temperature = 0
; before_layer_gcode =
; between_objects_gcode =
; bridge_acceleration = 0
; bridge_fan_speed = 100
; brim_connections_width = 0
; brim_ears = 0
; brim_ears_max_angle = 125
; brim_width = 0
; complete_objects = 0
; cooling = 1
; default_acceleration = 0
; disable_fan_first_layers = 3
; duplicate_distance = 6
; end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
; end_gcode = G1 E-5 F1000 ; Retract 5mm filament\nG91\nG1 Z50 F4000\nG90\nG1 X0 Y0\nT99\n\n
; extruder_clearance_height = 20
; extruder_clearance_radius = 20
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; fan_always_on = 1
; fan_below_layer_time = 60
; fan_percentage = 0
; filament_colour = #5EE9A0
; filament_cost = 20
; filament_density = 1.27
; filament_diameter = 1.73
; filament_max_volumetric_speed = 0
; filament_notes = ""
; first_layer_acceleration = 0
; first_layer_bed_temperature = 0
; first_layer_extrusion_width = 0.5
; first_layer_speed = 30
; first_layer_temperature = 220
; gcode_arcs = 0
; gcode_comments = 0
; gcode_flavor = reprap
; has_heatbed = 0
; infill_acceleration = 0
; infill_first = 0
; interior_brim_width = 0
; label_printed_objects = 0
; layer_gcode =
; max_fan_speed = 100
; max_layer_height = 0.3
; max_print_speed = 80
; max_volumetric_speed = 0
; min_fan_speed = 100
; min_layer_height = 0.15
; min_print_speed = 10
; min_skirt_length = 0
; notes =
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 1
; ooze_prevention = 0
; output_filename_format = [input_filename_base].gcode
; perimeter_acceleration = 0
; post_process =
; pressure_advance = 0
; printer_notes =
; resolution = 0
; retract_before_travel = 2
; retract_layer_change = 1
; retract_length = 2
; retract_length_toolchange = 10
; retract_lift = 0.4
; retract_lift_above = 0
; retract_lift_below = 0
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 25
; skirt_distance = 10
; skirt_height = 1
; skirts = 2
; slowdown_below_layer_time = 5
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "; Filament gcode\n"
; start_gcode = M83\nT0\nM116\nG1 E5 F1000 ; extrude 5mm filament
; temperature = 220
; threads = 4
; toolchange_gcode =
; travel_speed = 150
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; use_set_and_wait_bed = 0
; use_set_and_wait_extruder = 0
; use_volumetric_e = 0
; vibration_limit = 0
; wipe = 0
; z_offset = 0
; z_steps_per_mm = 0
; adaptive_slicing = 0
; adaptive_slicing_quality = 75%
; dont_support_bridges = 1
; extrusion_width = 0.5
; first_layer_height = 0.2
; infill_only_where_needed = 0
; interface_shells = 0
; layer_height = 0.2
; match_horizontal_surfaces = 0
; raft_layers = 0
; regions_overlap = 0
; seam_position = aligned
; sequential_print_priority = 0
; support_material = 0
; support_material_angle = 0
; support_material_buildplate_only = 0
; support_material_contact_distance = 0.2
; support_material_enforce_layers = 0
; support_material_extruder = 1
; support_material_extrusion_width = 0
; support_material_interface_extruder = 1
; support_material_interface_extrusion_width = 0
; support_material_interface_layers = 3
; support_material_interface_spacing = 0
; support_material_interface_speed = 100%
; support_material_max_layers = 0
; support_material_pattern = pillars
; support_material_pillar_size = 2.5
; support_material_pillar_spacing = 10
; support_material_spacing = 2.5
; support_material_speed = 60
; support_material_threshold = 60%
; xy_size_compensation = 0
; bottom_infill_pattern = rectilinear
; bottom_solid_layers = 2
; bridge_flow_ratio = 1
; bridge_speed = 60
; external_perimeter_extrusion_width = 0.5
; external_perimeter_speed = 40
; external_perimeters_first = 0
; extra_perimeters = 1
; fill_angle = 45
; fill_density = 10%
; fill_gaps = 1
; fill_pattern = gyroid
; gap_fill_speed = 40
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.5
; infill_overlap = 55%
; infill_speed = 40
; min_shell_thickness = 0
; min_top_bottom_shell_thickness = 0
; overhangs = 1
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.5
; perimeter_speed = 40
; perimeters = 3
; small_perimeter_speed = 40
; solid_infill_below_area = 10
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.5
; solid_infill_speed = 40
; thin_walls = 1
; top_infill_extrusion_width = 0.5
; top_infill_pattern = rectilinear
; top_solid_infill_speed = 40
; top_solid_layers = 4