root@hpserv:~# smartctl -x /dev/sdb
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.19.17-Unraid] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD40EFRX-68N32N0
Serial Number: WD-WCC7K7XJEU4R
LU WWN Device Id: 5 0014ee 26575d6e0
Firmware Version: 82.00A82
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database 7.3/5417
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Aug 12 11:17:25 2023 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 249) Self-test routine in progress...
90% of test remaining.
Total time to complete Offline
data collection: (44340) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 470) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 167 164 021 - 6633
4 Start_Stop_Count -O--CK 093 093 000 - 7985
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 056 056 000 - 32768
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 333
192 Power-Off_Retract_Count -O--CK 200 200 000 - 63
193 Load_Cycle_Count -O--CK 198 198 000 - 8804
194 Temperature_Celsius -O---K 110 095 000 - 40
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 56 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 1689 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1689 [8] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 00 00 00 00 00 00 00 00 00 1d+21:05:13.010 SET FEATURES [Set transfer mode]
ef 00 10 00 06 00 00 00 00 00 00 00 00 1d+21:05:13.009 SET FEATURES [Enable SATA feature]
ef 00 90 00 06 00 00 00 00 00 00 00 00 1d+21:05:13.004 SET FEATURES [Disable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 00 00 1d+21:05:13.003 IDENTIFY DEVICE
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.677 SET FEATURES [Enable SATA feature]
Error 1688 [7] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 06 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 06 00 00 00 00 00 00 00 00 1d+21:05:13.009 SET FEATURES [Enable SATA feature]
ef 00 90 00 06 00 00 00 00 00 00 00 00 1d+21:05:13.004 SET FEATURES [Disable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 00 00 1d+21:05:13.003 IDENTIFY DEVICE
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.677 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.676 IDENTIFY DEVICE
Error 1687 [6] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 06 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 90 00 06 00 00 00 00 00 00 00 00 1d+21:05:13.004 SET FEATURES [Disable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 00 00 1d+21:05:13.003 IDENTIFY DEVICE
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.677 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.676 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 1d+21:05:04.676 SET FEATURES [Set transfer mode]
Error 1686 [5] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.677 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.676 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 1d+21:05:04.676 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.675 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.675 IDENTIFY DEVICE
Error 1685 [4] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 a0 08 1d+21:05:04.676 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.675 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.675 IDENTIFY DEVICE
ea 00 00 00 00 00 00 00 00 00 00 e0 08 1d+21:05:04.657 FLUSH CACHE EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.656 SET FEATURES [Enable SATA feature]
Error 1684 [3] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.675 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.675 IDENTIFY DEVICE
ea 00 00 00 00 00 00 00 00 00 00 e0 08 1d+21:05:04.657 FLUSH CACHE EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.656 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.655 IDENTIFY DEVICE
Error 1683 [2] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 00 00 00 00 00 00 00 a0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ea 00 00 00 00 00 00 00 00 00 00 e0 08 1d+21:05:04.657 FLUSH CACHE EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.656 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.655 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 1d+21:05:04.655 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.654 SET FEATURES [Enable SATA feature]
Error 1682 [1] occurred at disk power-on lifetime: 32767 hours (1365 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.656 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.655 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 1d+21:05:04.655 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 1d+21:05:04.654 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 1d+21:05:04.654 IDENTIFY DEVICE
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 32767 -
# 2 Short offline Completed without error 00% 32767 -
# 3 Short offline Completed without error 00% 27779 -
# 4 Short offline Completed without error 00% 26538 -
# 5 Short offline Completed without error 00% 26438 -
# 6 Extended offline Completed without error 00% 25788 -
# 7 Extended offline Completed without error 00% 25193 -
# 8 Extended offline Interrupted (host reset) 60% 22179 -
# 9 Short offline Completed without error 00% 21106 -
#10 Short offline Completed without error 00% 21106 -
#11 Short offline Completed without error 00% 21106 -
#12 Short offline Completed without error 00% 17785 -
#13 Short offline Completed without error 00% 17618 -
#14 Short offline Completed without error 00% 17471 -
#15 Short offline Completed without error 00% 17115 -
#16 Short offline Completed without error 00% 16638 -
#17 Short offline Completed without error 00% 13874 -
#18 Short offline Completed without error 00% 7345 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: DST executing in background (3)
Current Temperature: 40 Celsius
Power Cycle Min/Max Temperature: 34/40 Celsius
Lifetime Min/Max Temperature: 13/55 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/65 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (85)
Index Estimated Time Temperature Celsius
86 2023-08-12 03:20 33 **************
... ..( 20 skipped). .. **************
107 2023-08-12 03:41 33 **************
108 2023-08-12 03:42 34 ***************
... ..(128 skipped). .. ***************
237 2023-08-12 05:51 34 ***************
238 2023-08-12 05:52 33 **************
... ..( 21 skipped). .. **************
260 2023-08-12 06:14 33 **************
261 2023-08-12 06:15 34 ***************
... ..( 3 skipped). .. ***************
265 2023-08-12 06:19 34 ***************
266 2023-08-12 06:20 ? -
267 2023-08-12 06:21 35 ****************
268 2023-08-12 06:22 35 ****************
269 2023-08-12 06:23 35 ****************
270 2023-08-12 06:24 34 ***************
271 2023-08-12 06:25 34 ***************
272 2023-08-12 06:26 35 ****************
... ..( 2 skipped). .. ****************
275 2023-08-12 06:29 35 ****************
276 2023-08-12 06:30 36 *****************
... ..( 2 skipped). .. *****************
279 2023-08-12 06:33 36 *****************
280 2023-08-12 06:34 37 ******************
... ..( 3 skipped). .. ******************
284 2023-08-12 06:38 37 ******************
285 2023-08-12 06:39 38 *******************
... ..( 5 skipped). .. *******************
291 2023-08-12 06:45 38 *******************
292 2023-08-12 06:46 39 ********************
... ..( 5 skipped). .. ********************
298 2023-08-12 06:52 39 ********************
299 2023-08-12 06:53 40 *********************
300 2023-08-12 06:54 40 *********************
301 2023-08-12 06:55 40 *********************
302 2023-08-12 06:56 34 ***************
... ..( 37 skipped). .. ***************
340 2023-08-12 07:34 34 ***************
341 2023-08-12 07:35 33 **************
... ..( 28 skipped). .. **************
370 2023-08-12 08:04 33 **************
371 2023-08-12 08:05 34 ***************
... ..( 8 skipped). .. ***************
380 2023-08-12 08:14 34 ***************
381 2023-08-12 08:15 35 ****************
... ..( 14 skipped). .. ****************
396 2023-08-12 08:30 35 ****************
397 2023-08-12 08:31 36 *****************
... ..( 28 skipped). .. *****************
426 2023-08-12 09:00 36 *****************
427 2023-08-12 09:01 35 ****************
... ..( 14 skipped). .. ****************
442 2023-08-12 09:16 35 ****************
443 2023-08-12 09:17 34 ***************
... ..( 22 skipped). .. ***************
466 2023-08-12 09:40 34 ***************
467 2023-08-12 09:41 33 **************
... ..( 95 skipped). .. **************
85 2023-08-12 11:17 33 **************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 333 --- Lifetime Power-On Resets
0x01 0x010 4 32768 --- Power-on Hours
0x01 0x018 6 106545467113 --- Logical Sectors Written
0x01 0x020 6 293607503 --- Number of Write Commands
0x01 0x028 6 93143763897 --- Logical Sectors Read
0x01 0x030 6 450160254 --- Number of Read Commands
0x01 0x038 6 2000683008 --- Date and Time TimeStamp
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 21333 --- Spindle Motor Power-on Hours
0x03 0x010 4 21135 --- Head Flying Hours
0x03 0x018 4 8868 --- Head Load Events
0x03 0x020 4 0 --- Number of Reallocated Logical Sectors
0x03 0x028 4 2 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 63 --- Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 7 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 327686 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 40 --- Current Temperature
0x05 0x010 1 33 --- Average Short Term Temperature
0x05 0x018 1 28 --- Average Long Term Temperature
0x05 0x020 1 55 --- Highest Temperature
0x05 0x028 1 13 --- Lowest Temperature
0x05 0x030 1 47 --- Highest Average Short Term Temperature
0x05 0x038 1 19 --- Lowest Average Short Term Temperature
0x05 0x040 1 42 --- Highest Average Long Term Temperature
0x05 0x048 1 22 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 65 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 11671 --- Number of Hardware Resets
0x06 0x010 4 11766 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 4 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 2073 Vendor specific