U-Boot 1.1.3 (Apr 20 2015 - 13:25:55)

Board: RT5350F-OLinuXino DRAM:  32 MB
relocate_code Pointer at: 81fb4000
spi_wait_nsec: 42
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
.raspi_read: from:30000 len:1000
.=============================================================
RT5350F-OLinuXino UBoot Version: 4.0.0.0
--------------------------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Apr 20 2015  Time:13:25:55
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

 ##### The CPU freq = 360 MHZ ####
 estimate memory size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
.   Image Name:   MIPS OpenWrt Linux-4.14.109
   Created:      2019-04-03  13:01:59 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1418537 Bytes =  1.4 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:15a529
......................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

[    0.000000] Linux version 4.14.109 (stefan@ubuntu-development) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7728+1-ca8b4d684b)) #0 Wed Apr 3 13:01:59 2019
[    0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[    0.000000] MIPS: machine is Olimex RT5350F-OLinuXino-EVB+
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00040f44
[    0.000000] Readback ErrCtl register=00040f44
[    0.000000] Memory: 27780K/32768K available (3289K kernel code, 162K rwdata, 772K rodata, 184K init, 195K bss, 4988K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 360MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
[    0.000017] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
[    0.015703] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[    0.098032] pid_max: default: 32768 minimum: 301
[    0.107608] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.120727] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.144666] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.164246] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.176571] pinctrl core: initialized pinctrl subsystem
[    0.188037] NET: Registered protocol family 16
[    0.257929] rt2880_gpio 10000600.gpio: registering 22 gpios
[    0.269067] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[    0.282076] rt2880_gpio 10000660.gpio: registering 6 gpios
[    0.293037] rt2880_gpio 10000660.gpio: registering 6 irq handlers
[    0.315594] clocksource: Switched to clocksource MIPS
[    0.327798] NET: Registered protocol family 2
[    0.338098] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.351990] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.364565] TCP: Hash tables configured (established 1024 bind 1024)
[    0.377572] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.389220] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.402119] NET: Registered protocol family 1
[    0.417547] rt-timer 10000100.timer: maximum frequency is 3662Hz
[    0.431227] Crashlog allocated RAM at address 0x1f00000
[    0.446420] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[    0.469598] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.481194] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.528251] io scheduler noop registered
[    0.536031] io scheduler deadline registered (default)
[    0.548644] gpio-export gpio_export: 4 gpio(s) exported
[    0.559565] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.574192] 10000500.uart: ttyS1 at MMIO 0x10000500 (irq = 13, base_baud = 2500000) is a Palmchip BK-3103
[    0.594582] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.614396] console [ttyS0] enabled
[    0.614396] console [ttyS0] enabled
[    0.628172] bootconsole [early0] disabled
[    0.628172] bootconsole [early0] disabled
[    0.645118] cacheinfo: Failed to find cpu0 device node
[    0.655493] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.693131] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.702884] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.715616] Creating 4 MTD partitions on "spi0.0":
[    0.725185] 0x000000000000-0x000000030000 : "u-boot"
[    0.737114] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.749617] 0x000000040000-0x000000050000 : "factory"
[    0.761678] 0x000000050000-0x000000800000 : "firmware"
[    2.655624] random: fast init done
[    4.901788] 2 uimage-fw partitions found on MTD device firmware
[    4.913728] 0x000000050000-0x0000001aa569 : "kernel"
[    4.925437] 0x0000001aa569-0x000000800000 : "rootfs"
[    4.937229] mtd: device 5 (rootfs) set to be root filesystem
[    4.953002] 1 squashfs-split partitions found on MTD device rootfs
[    4.965496] 0x00000043e000-0x000000800000 : "rootfs_data"
[    4.985204] libphy: Fixed MDIO Bus: probed
[    5.001067] rt3050-esw 10110000.esw: link changed 0x00
[    5.013346] mtk_soc_eth 10100000.ethernet: generated random MAC address ea:3f:ef:eb:c1:09
[    5.031030] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    5.048642] rt2880_wdt 10000120.watchdog: Initialized
[    5.061328] NET: Registered protocol family 10
[    5.079809] Segment Routing with IPv6
[    5.087457] NET: Registered protocol family 17
[    5.096547] 8021q: 802.1Q VLAN Support v1.8
[    5.158765] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    5.174918] Freeing unused kernel memory: 184K
[    5.183914] This architecture does not have kernel memory protection.
[   10.741968] init: Console is alive
[   10.749505] init: - watchdog -
[   20.769095] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[   20.978015] usbcore: registered new interface driver usbfs
[   20.989326] usbcore: registered new interface driver hub
[   21.000339] usbcore: registered new device driver usb
[   21.073660] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   21.103371] SCSI subsystem initialized
[   21.121733] ehci-platform: EHCI generic platform driver
[   21.142908] phy phy-usbphy.0: remote usb device wakeup disabled
[   21.154789] phy phy-usbphy.0: UTMI 16bit 30MHz
[   21.163737] ehci-platform 101c0000.ehci: EHCI Host Controller
[   21.175394] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[   21.191572] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[   21.225676] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[   21.240266] hub 1-0:1.0: USB hub found
[   21.249062] hub 1-0:1.0: 1 port detected
[   21.264353] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   21.280072] ohci-platform: OHCI generic platform driver
[   21.291181] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[   21.304933] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[   21.321001] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[   21.401551] hub 2-0:1.0: USB hub found
[   21.410222] hub 2-0:1.0: 1 port detected
[   21.447168] usbcore: registered new interface driver usb-storage
[   21.465837] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[   21.491326] init: - preinit -
[   26.045711] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   29.486874] mount_root: loading kmods from internal overlay
[   29.563476] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   29.581914] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   35.036408] jffs2: notice: (383) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[   35.069736] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   35.120325] block: extroot: not configured
[   37.546665] jffs2: notice: (381) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[   40.688375] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   40.722308] block: extroot: not configured
[   40.735904] mount_root: switching to jffs2 overlay
[   40.838660] overlayfs: upper fs does not support tmpfile.
[   40.874487] urandom-seed: Seeding with /etc/urandom.seed
[   41.601911] procd: - early -
[   41.608110] procd: - watchdog -
[   42.401539] procd: - watchdog -
[   42.416622] procd: - ubus -
[   43.104080] random: ubusd: uninitialized urandom read (4 bytes read)
[   43.222460] random: ubusd: uninitialized urandom read (4 bytes read)
[   43.236095] random: ubusd: uninitialized urandom read (4 bytes read)
[   43.253012] procd: - init -
Please press Enter to activate this console.
[   43.986602] kmodloader: loading kernel modules from /etc/modules.d/*
[   44.025849] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   44.064454] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   44.107226] i2c /dev entries driver
[   44.119617] i2c-ralink 10000900.i2c: clock 100KHz, re-start support
[   44.146278] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   44.162366] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   44.187765] ip_tables: (C) 2000-2006 Netfilter Core Team
[   44.220438] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   44.344520] spidev spi1.0: buggy DT: spidev listed directly in DT
[   44.356830] ------------[ cut here ]------------
[   44.366126] WARNING: CPU: 0 PID: 492 at drivers/spi/spidev.c:731 0x80e1a200
[   44.380058] Modules linked in: spidev(+) slhc of_mmc_spi nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc7 crc_itu_t crc_ccitt compat i2c_ralink i2c_dev i2c_core ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables vfat fat ntfs nls_utf8 nls_iso8859_1 nls_cp437 eeprom_93cx6 mmc_block usb_storage mmc_core leds_gpio ohci_platform ohci_hcd ehci_platform sd_mod scsi_mod ehci_hcd gpio_button_hotplug ext4 jbd2 mbcache usbcore nls_base usb_common crc16 crc32c_generic crypto_hash
[   44.506133] CPU: 0 PID: 492 Comm: kmodloader Not tainted 4.14.109 #0
[   44.518847] Stack : 80453650 80358544 00000000 00000000 803b8280 80e8db4c 819d5e5c 803ff907
[   44.535596]         803b4608 000001ec 80453650 000002db 00000008 00000000 80e8db00 517eb4e7
[   44.552333]         00000000 00000000 80450000 00000000 000000a2 00000000 20646574 34312e34
[   44.569069]         65675f63 00000000 00000001 6972656e 80000000 00000000 80e1a200 80e1ae14
[   44.585808]         00000009 000002db 00000008 014000c0 00000003 801c2e2c 00000000 80450000
[   44.602544]         ...
[   44.607476] Call Trace:
[   44.612402] [<8000e414>] show_stack+0x74/0x104
[   44.621362] [<80024ca0>] __warn+0x110/0x118
[   44.629790] [<80024d3c>] warn_slowpath_null+0x1c/0x30
[   44.639951] [<80e1a200>] 0x80e1a200
[   44.646987] ---[ end trace ae99dbd352576019 ]---
[   44.699523] xt_time: kernel timezone is -0000
[   44.877227] mmc_spi spi0.1: SD/MMC host mmc0, no WP, no poweroff
[   44.902762] PPP generic driver version 2.4.2
[   44.917629] NET: Registered protocol family 24
[   44.987317] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[   45.001874] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[   45.017417] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[   45.056165] kmodloader: done loading kernel modules from /etc/modules.d/*
[   46.906288] urandom_read: 6 callbacks suppressed
[   46.906304] random: jshn: uninitialized urandom read (4 bytes read)
[   64.516191] device eth0 entered promiscuous mode
[   64.544035] br-lan: port 1(eth0.1) entered blocking state
[   64.554956] br-lan: port 1(eth0.1) entered disabled state
[   64.566485] device eth0.1 entered promiscuous mode
[   64.715872] br-lan: port 1(eth0.1) entered blocking state
[   64.726748] br-lan: port 1(eth0.1) entered forwarding state
[   64.738385] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   65.486519] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  124.105713] random: crng init done

BusyBox v1.28.4 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt 18.06-SNAPSHOT, r7728+1-ca8b4d684b
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------

root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/#