ELLO! BOOT0 is starting!------!-!
boot0 commit : 8
boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.0
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 7580 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000f0000.
sum=27f67567
src_sum=27f67567
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000b400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
Jump to secend Boot. J9= Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):0bc348a
NOTICE: BL3-1: Built : 01:16:30, Jan 4 2017
NOTICE: BL3-1 commit: 0bc348ab272ad81a4faf128ef38f4724f36fded6

INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3

U-Boot 2014.07-4-pine64-gfe9e539 (Jul 05 2017 - 14:41:57) Allwinner Technology

uboot commit : fe9e5397ffbe864e5beb946f596e75b924d34056

rsb: secure monitor exist
[ 0.401]pmbus: ready
[ 0.404][ARISC] :arisc initialize
[ 0.836][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc_para size:1a8
[SCP] :arisc version: [v0.1.76]
[SCP] :sunxi-arisc driver v1.10 is starting
[ 0.997][ARISC] :sunxi-arisc driver startup succeeded
[ 1.041]PMU: AXP81X
[ 1.043]PMU: AXP81X found
bat_vol=0, ratio=100
[ 1.050]PMU: dcdc2 1100
[ 1.054]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
device_type = 3253, onoff=1
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1100, onoff=1
dcdc6_vol = 1100, onoff=1
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dldo1_vol = 3300, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 3300, onoff=1
eldo1_vol = 1800, onoff=1
eldo2_vol = 1800, onoff=0
eldo3_vol = 1800, onoff=0
fldo1_vol = 1200, onoff=0
fldo2_vol = 1100, onoff=1
gpio0_vol = 3100, onoff=0
gpio1_vol = 3100, onoff=0
vbus exist
no battery, limit to dc
run key detect
no key found
no uart input
DRAM: 1008 MiB
fdt addr: 0x76eba640
Relocation Offset is: 35f0c000
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[ 1.394]start
drv_disp_init
init_clocks: finish init_clocks.
enable power vcc-hdmi-33, ret=0
drv_disp_init finish
boot_disp.output_disp=0
boot_disp.output_type=3
boot_disp.output_mode=10
fetch script data boot_disp.auto_hpd fail
disp0 device type(4) enable
attched ok, mgr0<-->device1, type=4, mode=10
[ 1.993]end
workmode = 0,storage type = 1
[ 1.998]MMC: 0
[mmc]: mmc driver ver 2015-06-03 13:50:00
SUNXI SD/MMC: 0
[mmc]: start mmc_calibrate_delay_unit, don't access device...
[mmc]: delay chain cal done, sample: 200(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 03 PSN 43b64ea3
[mmc]: PNM SL08G -- 0x53-4c-30-38-47
[mmc]: PRV 8.0
[mmc]: MDT m-8 y-2015
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 7580 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 2.334]sunxi flash init ok
[mmc]: Has init
[ 2.407]---drivers/mmc/mmc.c 2733 mmc_init
reading uboot.env
FAT: Misaligned buffer address (76e945e8)
--------fastboot partitions--------
mbr not exist
base bootcmd=run mmcbootcmd
bootcmd set setargs_mmc
key 0
recovery key high 12, low 10
fastboot key high 6, low 4
no misc partition is found
to be run cmd=run mmcbootcmd
update dtb dram start
update dtb dram end
serial is: 00000000000000000000
Model: a64-olinuxino
no battery exist
sunxi_bmp_logo_display
[mmc]: Has init
[ 3.029]---drivers/mmc/mmc.c 2733 mmc_init
reading bootlogo.bmp
3148922 bytes read in 158 ms (19 MiB/s)
bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1920, screen_height =1080
frame buffer address 47400036
[ 4.072]inter uboot shell
Hit any key to stop autoboot: 3 2 1 0
[mmc]: Has init
[ 7.295]---drivers/mmc/mmc.c 2733 mmc_init
reading uEnv.txt
[mmc]: blkcnt should not be 0
118 bytes read in 6 ms (18.6 KiB/s)
Loading boot environment ...
[mmc]: Has init
[ 7.315]---drivers/mmc/mmc.c 2733 mmc_init
reading boot.scr
** Unable to read file boot.scr **
Booting with defaults ...
[mmc]: Has init
[ 7.334]---drivers/mmc/mmc.c 2733 mmc_init
reading a64/a64-olinuxino.dtb
67677 bytes read in 8 ms (8.1 MiB/s)
[mmc]: Has init
[ 7.390]---drivers/mmc/mmc.c 2733 mmc_init
reading a64/Image
12044224 bytes read in 598 ms (19.2 MiB/s)
[mmc]: Has init
[ 7.999]---drivers/mmc/mmc.c 2733 mmc_init
reading initrd.gz
1104262 bytes read in 58 ms (18.2 MiB/s)
Image lacks image_size field, assuming 16MiB
## Flattened Device Tree blob at 45000000
Booting using the fdt blob at 0x45000000
reserving fdt memory region: addr=41010000 size=10000
reserving fdt memory region: addr=41020000 size=800
reserving fdt memory region: addr=40100000 size=4000
reserving fdt memory region: addr=40104000 size=1000
reserving fdt memory region: addr=40105000 size=1000
reserving fdt memory region: addr=45000000 size=11000
Loading Ramdisk to 76da5000, end 76eb2986 ... OK
Loading Device Tree to 44feb000, end 44ffefff ... OK

Starting kernel ...

[mmc]: MMC Device 2 not found
[mmc]: mmc 2 not find, so not exit
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c5
HELLO! BOOT0 is starting!------!-!
boot0 commit : 8
boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.0
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 7580 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000f0000.
sum=27f67567
src_sum=27f67567
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000b400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
Jump to secend Boot. J9= Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):0bc348a
NOTICE: BL3-1: Built : 01:16:30, Jan 4 2017
NOTICE: BL3-1 commit: 0bc348ab272ad81a4faf128ef38f4724f36fded6

INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3

U-Boot 2014.07-4-pine64-gfe9e539 (Jul 05 2017 - 14:41:57) Allwinner Technology

uboot commit : fe9e5397ffbe864e5beb946f596e75b924d34056

rsb: secure monitor exist
[ 0.401]pmbus: ready
[ 0.404][ARISC] :arisc initialize
[ 0.835][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc_para size:1a8
[SCP] :arisc version: [v0.1.76]
[SCP] :sunxi-arisc driver v1.10 is starting
[ 0.996][ARISC] :sunxi-arisc driver startup succeeded
[ 1.040]PMU: AXP81X
[ 1.042]PMU: AXP81X found
bat_vol=0, ratio=100
[ 1.049]PMU: dcdc2 1100
[ 1.052]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
device_type = 3253, onoff=1
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1100, onoff=1
dcdc6_vol = 1100, onoff=1
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dldo1_vol = 3300, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 3300, onoff=1
eldo1_vol = 1800, onoff=1
eldo2_vol = 1800, onoff=0
eldo3_vol = 1800, onoff=0
fldo1_vol = 1200, onoff=0
fldo2_vol = 1100, onoff=1
gpio0_vol = 3100, onoff=0
gpio1_vol = 3100, onoff=0
vbus exist
no battery, limit to dc
run key detect
no key found
no uart input
DRAM: 1008 MiB
fdt addr: 0x76eba640
Relocation Offset is: 35f0c000
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[ 1.392]start
drv_disp_init
init_clocks: finish init_clocks.
enable power vcc-hdmi-33, ret=0
drv_disp_init finish
boot_disp.output_disp=0
boot_disp.output_type=3
boot_disp.output_mode=10
fetch script data boot_disp.auto_hpd fail
disp0 device type(4) enable
attched ok, mgr0<-->device1, type=4, mode=10
[ 1.992]end
workmode = 0,storage type = 1
[ 1.996]MMC: 0
[mmc]: mmc driver ver 2015-06-03 13:50:00
SUNXI SD/MMC: 0
[mmc]: start mmc_calibrate_delay_unit, don't access device...
[mmc]: delay chain cal done, sample: 200(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 03 PSN 43b64ea3
[mmc]: PNM SL08G -- 0x53-4c-30-38-47
[mmc]: PRV 8.0
[mmc]: MDT m-8 y-2015
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 7580 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 2.332]sunxi flash init ok
[mmc]: Has init
[ 2.405]---drivers/mmc/mmc.c 2733 mmc_init
reading uboot.env
FAT: Misaligned buffer address (76e945e8)
--------fastboot partitions--------
mbr not exist
base bootcmd=run mmcbootcmd
bootcmd set setargs_mmc
key 0
recovery key high 12, low 10
fastboot key high 6, low 4
no misc partition is found
to be run cmd=run mmcbootcmd
update dtb dram start
update dtb dram end
serial is: 00000000000000000000
Model: a64-olinuxino
no battery exist
sunxi_bmp_logo_display
[mmc]: Has init
[ 3.028]---drivers/mmc/mmc.c 2733 mmc_init
reading bootlogo.bmp
3148922 bytes read in 158 ms (19 MiB/s)
bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1920, screen_height =1080
frame buffer address 47400036
[ 4.071]inter uboot shell
Hit any key to stop autoboot: 3 2 1 0
[mmc]: Has init
[ 7.294]---drivers/mmc/mmc.c 2733 mmc_init
reading uEnv.txt
[mmc]: blkcnt should not be 0
118 bytes read in 6 ms (18.6 KiB/s)
Loading boot environment ...
[mmc]: Has init
[ 7.314]---drivers/mmc/mmc.c 2733 mmc_init
reading boot.scr
** Unable to read file boot.scr **
Booting with defaults ...
[mmc]: Has init
[ 7.333]---drivers/mmc/mmc.c 2733 mmc_init
reading a64/a64-olinuxino.dtb
67677 bytes read in 9 ms (7.2 MiB/s)
[mmc]: Has init
[ 7.389]---drivers/mmc/mmc.c 2733 mmc_init
reading a64/Image
12044224 bytes read in 598 ms (19.2 MiB/s)
[mmc]: Has init
[ 7.999]---drivers/mmc/mmc.c 2733 mmc_init
reading initrd.gz
1104262 bytes read in 58 ms (18.2 MiB/s)
Image lacks image_size field, assuming 16MiB
## Flattened Device Tree blob at 45000000
Booting using the fdt blob at 0x45000000
reserving fdt memory region: addr=41010000 size=10000
reserving fdt memory region: addr=41020000 size=800
reserving fdt memory region: addr=40100000 size=4000
reserving fdt memory region: addr=40104000 size=1000
reserving fdt memory region: addr=40105000 size=1000
reserving fdt memory region: addr=45000000 size=11000
Loading Ramdisk to 76da5000, end 76eb2986 ... OK
Loading Device Tree to 44feb000, end 44ffefff ... OK

Starting kernel ...

[mmc]: MMC Device 2 not found
[mmc]: mmc 2 not find, so not exit
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c5
HELLO! BOOT0 is starting!------!-!
boot0 commit : 8
boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.0
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 7580 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000f0000.
sum=27f67567
src_sum=27f67567
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000b400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
Jump to secend Boot. %9= Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):0bc348a
NOTICE: BL3-1: Built : 01:16:30, Jan 4 2017
NOTICE: BL3-1 commit: 0bc348ab272ad81a4faf128ef38f4724f36fded6

INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3

U-Boot 2014.07-4-pine64-gfe9e539 (Jul 05 2017 - 14:41:57) Allwinner Technology

uboot commit : fe9e5397ffbe864e5beb946f596e75b924d34056

rsb: secure monitor exist
[ 0.403]pmbus: ready
[ 0.406][ARISC] :arisc initialize
[ 0.834][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
[SCP] :sunxi-arisc driver begin startup 2
[SCP] :arisc_para size:1a8
[SCP] :arisc version: [v0.1.76]
[SCP] :sunxi-arisc driver v1.10 is starting
[ 0.994][ARISC] :sunxi-arisc driver startup succeeded
[ 1.038]PMU: AXP81X
[ 1.040]PMU: AXP81X found
bat_vol=0, ratio=100
[ 1.047]PMU: dcdc2 1100
[ 1.050]PMU: cpux 1008 Mhz,AXI=336 Mhz
PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
device_type = 3253, onoff=1
dcdc1_vol = 3300, onoff=1
dcdc2_vol = 1100, onoff=1
dcdc6_vol = 1100, onoff=1
aldo1_vol = 3300, onoff=1
aldo2_vol = 1800, onoff=1
aldo3_vol = 3000, onoff=1
dldo1_vol = 3300, onoff=0
dldo2_vol = 3300, onoff=0
dldo3_vol = 2800, onoff=0
dldo4_vol = 3300, onoff=1
eldo1_vol = 1800, onoff=1
eldo2_vol = 1800, onoff=0
eldo3_vol = 1800, onoff=0
fldo1_vol = 1200, onoff=0
fldo2_vol = 1100, onoff=1
gpio0_vol = 3100, onoff=0
gpio1_vol = 3100, onoff=0
vbus exist
no battery, limit to dc
run key detect
no key found
no uart input
DRAM: 1008 MiB
fdt addr: 0x76eba640
Relocation Offset is: 35f0c000
In: serial
Out: serial
Err: serial
gic: sec monitor mode
[ 1.390]start
drv_disp_init
init_clocks: finish init_clocks.
enable power vcc-hdmi-33, ret=0
drv_disp_init finish
boot_disp.output_disp=0
boot_disp.output_type=3
boot_disp.output_mode=10
fetch script data boot_disp.auto_hpd fail
disp0 device type(4) enable
attched ok, mgr0<-->device1, type=4, mode=10
[ 1.981]end
workmode = 0,storage type = 1
[ 1.985]MMC: 0
[mmc]: mmc driver ver 2015-06-03 13:50:00
SUNXI SD/MMC: 0
[mmc]: start mmc_calibrate_delay_unit, don't access device...
[mmc]: delay chain cal done, sample: 200(ps)
[mmc]: media type 0x0
[mmc]: Wrong media type 0x0
[mmc]: ************Try SD card 0************
[mmc]: host caps: 0x27
[mmc]: MID 03 PSN 43b64ea3
[mmc]: PNM SL08G -- 0x53-4c-30-38-47
[mmc]: PRV 8.0
[mmc]: MDT m-8 y-2015
[mmc]: speed mode : HSSDR52/SDR25
[mmc]: clock : 50000000 Hz
[mmc]: bus_width : 4 bit
[mmc]: user capacity : 7580 MB
[mmc]: ************SD/MMC 0 init OK!!!************
[mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
[mmc]: secure_feature : 0x0
[mmc]: secure_removal_type : 0x0
[ 2.314]sunxi flash init ok
[mmc]: Has init
[ 2.385]---drivers/mmc/mmc.c 2733 mmc_init
reading uboot.env
FAT: Misaligned buffer address (76e945e8)
--------fastboot partitions--------
mbr not exist
base bootcmd=run mmcbootcmd
bootcmd set setargs_mmc
key 0
recovery key high 12, low 10
fastboot key high 6, low 4
no misc partition is found
to be run cmd=run mmcbootcmd
update dtb dram start
update dtb dram end
serial is: 00000000000000000000
Model: a64-olinuxino
no battery exist
sunxi_bmp_logo_display
[mmc]: Has init
[ 2.993]---drivers/mmc/mmc.c 2733 mmc_init
reading bootlogo.bmp
3148922 bytes read in 158 ms (19 MiB/s)
bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
fetch script data boot_disp.output_full fail
screen_id =0, screen_width =1920, screen_height =1080
frame buffer address 47400036
[ 4.024]inter uboot shell
Hit any key to stop autoboot: 3 2 1 0
[mmc]: Has init
[ 7.242]---drivers/mmc/mmc.c 2733 mmc_init
reading uEnv.txt
[mmc]: blkcnt should not be 0
118 bytes read in 5 ms (22.5 KiB/s)
Loading boot environment ...
[mmc]: Has init
[ 7.262]---drivers/mmc/mmc.c 2733 mmc_init
reading boot.scr
** Unable to read file boot.scr **
Booting with defaults ...
[mmc]: Has init
[ 7.280]---drivers/mmc/mmc.c 2733 mmc_init
reading a64/a64-olinuxino.dtb
67677 bytes read in 9 ms (7.2 MiB/s)
[mmc]: Has init
[ 7.335]---drivers/mmc/mmc.c 2733 mmc_init
reading a64/Image
12044224 bytes read in 595 ms (19.3 MiB/s)
[mmc]: Has init
[ 7.942]---drivers/mmc/mmc.c 2733 mmc_init
reading initrd.gz
1104262 bytes read in 58 ms (18.2 MiB/s)
Image lacks image_size field, assuming 16MiB
## Flattened Device Tree blob at 45000000
Booting using the fdt blob at 0x45000000
reserving fdt memory region: addr=41010000 size=10000
reserving fdt memory region: addr=41020000 size=800
reserving fdt memory region: addr=40100000 size=4000
reserving fdt memory region: addr=40104000 size=1000
reserving fdt memory region: addr=40105000 size=1000
reserving fdt memory region: addr=45000000 size=11000
Loading Ramdisk to 76da5000, end 76eb2986 ... OK
Loading Device Tree to 44feb000, end 44ffefff ... OK

Starting kernel ...

[mmc]: MMC Device 2 not found
[mmc]: mmc 2 not find, so not exit
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c5
HELLO! BOOT0 is starting!------!-!
boot0 commit : 8
boot0 version : 4.0.0
set pll start
set pll end
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
DRAM driver version: V1.0
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM clk = 672 MHz
DRAM zq value: 003b3bbb
rsb_send_initseq: rsb clk 400Khz -> 3Mhz
PMU: AXP81X
ddr voltage = 1500 mv
DRAM single rank full DQ OK
DRAM size = 1024 MB
DRAM init ok
dram size =1024
card boot number = 0, boot0 copy = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2015-05-08 20:06
[mmc]: sdc0 spd mode error, 2
[mmc]: Wrong media type 0x00000000
[mmc]: ***Try SD card 0***
[mmc]: HSSDR52/SDR25 4 bit
[mmc]: 50000000 Hz
[mmc]: 7580 MB
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000f0000.
sum=27f67567
src_sum=27f67567
Succeed in loading uboot from sdmmc flash.
boot0: start load other image
boot0: Loading BL3-1
Loading file 0 at address 0x40000000,size 0x0000b400 success
boot0: Loading scp
Loading file 2 at address 0x00040000,size 0x00019c00 success
set arisc reset to de-assert state
Ready to disable icache.
Jump to secend Boot. J9= Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):0bc348a
NOTICE: BL3-1: Built : 01:16:30, Jan 4 2017
NOTICE: BL3-1 commit: 0bc348ab272ad81a4faf128ef38f4724f36fded6

INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x4a000000
INFO: BL3-1: Next image spsr = 0x1d3

U-Boot 2014.07-4-pine64-gfe9e539 (Jul 05 2017 - 14:41:57) Allwinner Technology

uboot commit : fe9e5397ffbe864e5beb946f596e75b924d34056

rsb: secure monitor exist
[ 0.401]pmbus: ready
[ 0.404][ARISC] :arisc initialize
[ 0.836][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table